63-87 C10 Truck Front K-Member and Parts (This K-Member and Control Arms are designed to work Specificly together. Factory components Will Not Work)
$19.98 – $1,645.05 Each
The Skyview Racing C10 K-Member (KIT)is a bolt in suspension package for 63-87 Pickups. Some fabrication work required, but in general this is a bolt in k-member. The factory dimples for the steering box and idler arms will need to be removed, and the factory frame may need to be notched for the steering shaft to clear headers. Line the back 2 bottom factory holes up and drill other holes in your frame and the K-Member and it bolts into place. Fabricate new steering shaft.
- Complete Kit Weighs 155 lbs Total
- Save 175# with our complete kit!!!
- Fits 63 -87 C-10 Trucks
- 1.625″ OD 4130 Chrome Moly Steel, Tig Welded
- 64″ track width
- Includes Shock Mounts, Travel Limiter Mounts and Tie Down points
- Setup for Rack & Pinion Steering Box
- Shipped Powder coated black.
- Available with Chrome Moly A-Arms with Adjustable Heim Mounts
- K-Member weight 30lbs (less a-arms, shocks,brakes, etc.)
Ships finished with k-member Powder Coated Black, Control Arms come Silver Vein Coated.
Mounting Hardware NOT included.
INSTALLATION INSTRUCTIONS
-REMOVE THE FACTORY K MEMBER BY REMOVING ALL BOLTS AND GRINDING RIVITS HEADS OFF
-CUT AND REMOVE THE FACTORY DIMPLES IN FRAME WHERE STEERING BOX AND IDLER ARMS WERE LOCATED. (WE RECOMMEND USING STEEL PLATE TO PATCH THE HOLES IN FRAME)
-DRIVERS SIDE OF FACTORY FRAME MAY NEED TO BE NOTCHED FOR STEERING SHAFT TO CLEAR HEADERS
-THE BACK 2 HOLES ON FACTORY K MEMBER WILL LINE UP WITH THE BACK 2 HOLES ON OUR BOLT IN K MEMBER. YOU WILL HAVE TO DRILL THE REST OF THE HOLES WITH A 1/2″ DRILL BIT
-USING THE 1/2-20 GRADE 8 BOLTS AND NUTS SUPPLIED BOLT K MEMBER TO FRAME RAILS (THE REAR LOWER CONTROL ARM BUCKET SHOULD BE INLINE WITH YOUR SPINDLE)
– INSTALL UPPER/LOWER CONTROL ARMS. USING THE WEHR SPACERS SUPPLIED BOLT LOWER ARMS ON WITH LIMITER TABS FACING REAR OF TRUCK. (A GOOD STARTING POINT WILL BE TO SET YOUR HEIMS 5 TURNS OUT FROM ALL THE WAY IN)
-BOLT ON BILLET STEERING ARMS TO 1ST GEN CAMARO SPINDLES
-INSTALL BRAKE KIT USING 3/4-20 SPINDLE NUTS. INSTALL SHOCKS/SPRINGS (WE USUALLY SET SPRING COLLARS FOR A 6″ RIDE HEIGHT FROM THE ROCKER TO GROUND)
-24″ TRAVEL LIMITERS WILL BOLT TO THE 3/8 REAR FACING HOLE IN UPPER SHOCK MOUNTS. CABLE GOES THROUGH TAB ON LOWER ARM WITH THE CLAMPS SUPPLIED
-USING THE BILLET RACK MOUNT BOLT YOUR RACK TO K MEMBER AND INSTALL THE TIE ROD AND BUMP STEER KIT TO STEERING ARM
REFER TO PICTURES ON WEBSITE OF HOW COMPLETED ASSEMBLY SHOULD LOOK
Ships Truck Freight, Billed Separately after Checkout.
- Specifications
- Reviews (0)
Applications: 1963-1987 Chevy/GMC C10 Pickups
Shock Length: 12-16.9″ Length
Shock Mount: Heim Upper & Lower
Empty K-Member Weight: 30 lbs
Be the first to review “63-87 C10 Truck Front K-Member and Parts (This K-Member and Control Arms are designed to work Specificly together. Factory components Will Not Work)” Cancel reply
You must be logged in to post a review.
You may also like…
-
-
C-10 Upper and Lower Control Arm Kit SVRC-110010(ONLY FITS OUR K-MEMBER)
$1,645.05 Complete Set -
Reviews
There are no reviews yet.